Тип публикации: патент
Год издания: 2022
Аннотация: Изобретение относится к горному делу, а именно к сооружению наклонных горных выработок в условиях высокого горного давления. Монолитная железобетонная крепь наклонной горной выработки, состоящая из бетонного тела и каркаса включающего: арматурные прутки вдоль наклонной выработки, арматурные прутки поперек основания наклонной выработки, арматурные прутки, перпендикулярные к основанию наклонной выработки, и стальную арматуру по дуге свода, а также армируемые поперечные скобы, с шагом, соответствующим расчетному шагу армирования, выполненные в поперечном сечении эллипсовидной формы. Длинная ось эллипса арматуры совмещена с максимальными нагрузками на каркас железобетонной крепи наклонной выработки. Для арматурных прутков вдоль наклонной выработки максимальный момент сопротивления по длинной оси эллипса совмещен с перпендикуляром к боковой поверхности, основанию, а также с радиусом сегмента окружности свода наклонной горной выработки, соответственно их расположению. Для арматурных прутков поперек основания и перпендикулярных основанию наклонной выработки максимальный момент сопротивления по длинной оси эллипса арматуры совмещен с перпендикуляром к основанию и к боковой поверхности наклонной горной выработки, соответственно. Для стальной арматуры, установленной по дуге свода в виде сегмента окружности наклонной горной выработки, максимальный момент сопротивления по длинной оси эллипса арматуры совмещен с радиусом сегмента окружности каркаса. Для арматурных прутков вдоль наклонной выработки, установленных в углах основания и боковой поверхности, максимальный момент сопротивления по длинной оси эллипса арматуры совмещен с диагональю между соответствующими перпендикулярами на эти поверхности. Для армируемых поперечных скоб, установленных на арматурные прутки в каркасе: поперек основания наклонной выработки, перпендикулярные к основанию наклонной выработки, и стальную арматуру по дуге свода наклонной выработки, максимальный момент сопротивления по длинной оси эллипса арматуры установлен параллельно линии угла наклона горной выработки. Для армируемых поперечных скоб, установленных на арматурные прутки вдоль наклонной выработки, максимальный момент сопротивления по длинной оси эллипса арматуры установлен параллельно следу плоскости, проведенной через эту скобу, на боковой поверхности, основании наклонной выработки, а также касательной в точке выхода радиуса на дугу арматуры, соответственно их расположению. Техническим результатом является повышение надежности монолитной железобетонной крепи наклонной горной выработки. 6 ил., 1 табл. FIELD: mining. SUBSTANCE: invention relates to mining, namely the construction of inclined mine workings under conditions of high rock pressure. Monolithic reinforced concrete support of an inclined mine working, consisting of a concrete body and a frame including: reinforcing bars along the inclined working, reinforcing bars across the base of the inclined working, reinforcing bars perpendicular to the base of the inclined working, and steel reinforcement along the arch of the arch, as well as reinforced transverse brackets, with a step corresponding to the calculated reinforcement step, made in an elliptical cross section. The long axis of the reinforcement ellipse is aligned with the maximum loads on the frame of the reinforced concrete lining of the inclined working. For reinforcing bars along an inclined mine working, the maximum moment of resistance along the long axis of the ellipse is aligned with the perpendicular to the side surface, the base, and also with the radius of the circle segment of the roof of the inclined mine working, according to their location. For reinforcing bars across the base and perpendicular to the base of the inclined mine working, the maximum moment of resistance along the long axis of the reinforcement ellipse is aligned with the perpendicular to the base and to the side surface of the inclined mine working, respectively. For steel reinforcement installed along the arch of the arch in the form of a segment of the circle of an inclined mine working, the maximum moment of resistance along the long axis of the reinforcement ellipse is combined with the radius of the segment of the circle of the frame. For reinforcing bars along an inclined working, installed at the corners of the base and the side surface, the maximum moment of resistance along the long axis of the reinforcement ellipse is aligned with the diagonal between the corresponding perpendiculars to these surfaces. For reinforced transverse brackets installed on reinforcing bars in the frame: across the base of the inclined working, perpendicular to the base of the inclined working, and steel reinforcement along the arc of the roof of the inclined working, the maximum moment of resistance along the long axis of the reinforcement ellipse is set parallel to the line of the angle of the mine working. For reinforced transverse brackets mounted on reinforcing bars along an inclined working, the maximum modulus of resistance along the long axis of the reinforcement ellipse is set parallel to the trace of the plane drawn through this bracket, on the side surface, the base of the inclined working, as well as the tangent at the point of exit of the radius to the reinforcement arc, according to their location. EFFECT: increasing the reliability of monolithic reinforced concrete lining of inclined mine workings. 1 cl, 6 dwg, 1 tbl