Тип публикации: статья из журнала

Год издания: 2023

Идентификатор DOI: 10.1016/j.ijlmm.2022.09.005

Ключевые слова: combined rolling-extrusion, drawing, mechanical properties, recycling of chip, rolling, structure

Аннотация: The article presents the results of studies that make it possible to solve the problem of processing secondary waste from expensive aluminum alloys without irretrievable loss of metal. For this purpose, tasks were set and solved for the development of technological schemes for obtaining longish deformed semi-finished products from Показать полностьюchip waste of Al–Mg alloys 01570 and 1580 alloyed with scandium using methods of powder metallurgy and metal forming. For their experimental verification, the operations of chip briquetting, combined rolling-extrusion (continuous extrusion), sectional rolling, hot extrusion and drawing in combination with heat treatment were applied. According to these schemes, semi-finished products in the form of rods and wires were obtained. Structure and mechanical properties were investigated. It has been revealed that when hot-extruded rods are obtained from chip briquettes of alloy 01570 on a vertical hydraulic press, even with significant degrees of deformation during extrusion, the margin of plastic properties is small and makes it possible to obtain a wire with a diameter of only 4.2 mm after drawing. The processing of briquettes from 1580 alloy chips using the combined rolling-extrusion method makes it possible to obtain after cold deformation a wire with a diameter of up to 3 mm. At the same time, the influence of the annealing process on the structure and properties of deformed semi-finished products from the investigated alloys was studied. It is shown that due to the low plasticity of the investigated material cold working of the rods must be carried out with small degrees of deformation, alternating it with intermediate annealing according to the proposed regime. An analysis of the physical and mechanical properties of the wire obtained using combined processing showed that its strength and plastic properties are comparable to the properties of the wire obtained from a cast billet, and the structure is characterized by a high degree of elaboration and compactness. Thus, as a result of the research, technological schemes have been developed and processing parameters have been determined for the production of rods and wire from graded chip waste of alloys 01570 and 1580 using compaction, discrete and continuous extrusion, as well as cold drawing. © 2022 The Authors

Журнал: International Journal of Lightweight Materials and Manufacture

Выпуск журнала: Vol. 6, Is. 1

Номера страниц: 46-58

ISSN журнала: 25888404

Издатель: KeAi Publishing Communications Ltd.

• Sidelnikov S.B. (Siberian Federal University, Krasnoyarsk Region, Krasnoyarsk, 660025, Russian Federation, Metal Forming Department, School of Non-Ferrous Metals and Material Science, SibFU, Honored Inventor of the Russian Federation, 95, Ave. Imeni gazeti Krasnoyarskiy rabochiy, Krasnoyarsk, 660025, Russian Federation)
• Zagirov N.N. (Siberian Federal University, Krasnoyarsk Region, Krasnoyarsk, 660025, Russian Federation, Metal Forming Department, School of Non-Ferrous Metals and Material Science, SibFU, 95, Ave. Imeni gazeti Krasnoyarskiy rabochiy, Krasnoyarsk, 660025, Russian Federation)
• Loginov Y.N. (Ural Federal University Named After the First President of Russia B.N. Yeltsin, Yekaterinburg, 620002, Russian Federation, Ural Federal University Named After the First President of Russia B.N. Yeltsin, 19, Mira, Yekaterinburg, 620002, Russian Federation)
• Lopatina E.S. (Siberian Federal University, Krasnoyarsk Region, Krasnoyarsk, 660025, Russian Federation, Department of Metal Science and Heat Treatment of Metals Named After V.S. Biront, School of Non-Ferrous Metals and Material Science, SibFU, 95, Ave. Imeni gazeti Krasnoyarskiy rabochiy, Krasnoyarsk, 660025, Russian Federation)
• Voroshilov D.S. (Siberian Federal University, Krasnoyarsk Region, Krasnoyarsk, 660025, Russian Federation, Metal Forming Department, School of Non-Ferrous Metals and Material Science, SibFU, 95, Ave. Imeni gazeti Krasnoyarskiy rabochiy, Krasnoyarsk, 660025, Russian Federation)
• Lezhnev S.N. (Rudny Industrial Institute, Rudny, 111500, Kazakhstan)
• Ivanov E.V. (Siberian Federal University, Krasnoyarsk Region, Krasnoyarsk, 660025, Russian Federation, Metal Forming Department, School of Non-Ferrous Metals and Material Science, SibFU, 95, Ave. Imeni gazeti Krasnoyarskiy rabochiy, Krasnoyarsk, 660025, Russian Federation)
• Saparova A.S. (Siberian Federal University, Krasnoyarsk Region, Krasnoyarsk, 660025, Russian Federation, Department of Metal Science and Heat Treatment of Metals Named After V.S. Biront, School of Non-Ferrous Metals and Material Science, SibFU, 95, Ave. Imeni gazeti Krasnoyarskiy rabochiy, Krasnoyarsk, 660025, Russian Federation)
• Voroshilova M.V. (Siberian Federal University, Krasnoyarsk Region, Krasnoyarsk, 660025, Russian Federation, Metal Forming Department, School of Non-Ferrous Metals and Material Science, SibFU, 95, Ave. Imeni gazeti Krasnoyarskiy rabochiy, Krasnoyarsk, 660025, Russian Federation)
• Ber V.I. (Siberian Federal University, Krasnoyarsk Region, Krasnoyarsk, 660025, Russian Federation, Metal Forming Department, School of Non-Ferrous Metals and Material Science, SibFU, Honored Machine Builder of Russia, 95, Ave. Imeni gazeti Krasnoyarskiy rabochiy, Krasnoyarsk, 660025, Russian Federation)
• Feskova E.V. (Siberian Federal University, Krasnoyarsk Region, Krasnoyarsk, 660025, Russian Federation, CDIO, School of Non-Ferrous Metals and Material Science, SibFU, 95, Ave. Imeni gazeti Krasnoyarskiy rabochiy, Krasnoyarsk, 660025, Russian Federation)
• Zagirova E.V. (Siberian Federal University, Krasnoyarsk Region, Krasnoyarsk, 660025, Russian Federation, Metal Forming Department, School of Non-Ferrous Metals and Material Science, SibFU, 95, Ave. Imeni gazeti Krasnoyarskiy rabochiy, Krasnoyarsk, 660025, Russian Federation)

• Scopus